YET850 with two parts YET850-M and YET850-S, it is the Programmable wireless remote controls signal receiver.
Features
• The receiver is designed to receive control commands from the wireless key fob and then run these commands in the form of activation of the 4 output relays.
• Storing trinkets in memory, as well as their selective removal is carried out via the programming YET850-S.
• Receiver programmer allows you to view information about registered key fob allows you to check whether the Keychain is registered in the memory.
• Power receiver universal, it can feed both AC and DC with a wide range of supply voltages, which allows the receiver to any automation (barriers, gates, shutters, etc.)
Specifications
Power supply: 10 - 36V AC / DC
Operating frequency: 433.92 MHz
The consumption of no more than 10 mA in the standby
Signal Modulation: ASK
Output relay: normally open, 20 A / 14 V DC, 7 A 120 V AC
Programmer: YET850-S
Memory capacity: 250 remotes
Products review:
YET850-M
Noted:
The green LED indicates normal operation in the standby mode.
The yellow LED indicates the signal reception or programming mode.
YET850-S:
Noted: Any number of receivers YET850-M can be programmed using the programmer YET850-S.
Remote control/keyfob pair:
All YET produced with 4 keys with 433.92MHz Rolling code
Such as :
Setting the operating mode of the receiver outputs
Buttons transmitter A, B, C, D are used to control channels 1, 2, 3, 4, respectively.
output channels Relay Mode is set J2 jumper on the receiver board.
• If the jumper is J2, the output relays and relay monostable mode and spend time the button is pressed. The relay is activated when you press the key fob button and turns off when you release the key fob buttons.
• If the jumper is J2, the output mode of the bistable relay. Each time you press the key fob button switches the relay to its opposite state and stays there until you press the corresponding button on the key fob.
Receiver Controller Setup with Programmer
Connect programmer TSt-PRG to the USB port of the receiver on the display programmer will display "- - - -", it indicates a successful connection.
Note: USB connectors of the receiver and not the programmer intended for connection to a computer.
Assigning programming buttons (left to right):
Button 1: The mode switch (playback, recording, removing the key fob, scan, delete all).
Button 2: ↑ increase addresses for key fob
Button 3: ↓ decrease addresses for key fob
Button 4: OK acknowledgment (OK)
A View: Press 1 to switch programming modes, select the mode which is displayed by the letter A. Use button 2 or 3 to select the desired transmitter to check the addresses (1-250), press the button 4 (OK). For example, if you want to know whether the key fob with an address of 100, set button 2 or 3 e 100 (displayed as "A100") is programmed and press 4 (OK). If this address is programmed key ring, the display will show "A888" if the key fob is not programmed, on the display will show "A - - -".
b. Register: Press 1 to switch programming modes, select the mode which is displayed by the letter b. Use buttons 2 or 3 to select the registration address of the new transmitter (1-250), press the button 4 (OK). For example, if you want to register a holder addresses 100, set button 2 or 3 e 100 (displayed as "B100") and press the button 4 (OK). Press any button on the key fob, if the registration is successful, the display will show "B888", if the key fob is not registered, the display will show "B - - -."
C. Removal of the key fob: press 1 to switch programming modes, select the mode which is displayed by the letter S. Press 2 or 3 to select the address to be removed keyfob (1-250), press the button 4 (OK). For example, if you want to remove the key fob to the address 100, set button 2 or 3 e 100 (displayed as "C100") and press the button 4 (OK). If the key fob is removed successfully, the display will show "S888" if the key fob is not removed, the display will show "C - - -."
d. Scan: Press 1 to switch programming modes, select the mode which is displayed by d and press 4 (OK). The display will show «D - - -». Press any button on the key fob audited if keychain is registered in the receiver's address is displayed on the display, eg «D100». If the key fob is not registered in the receiver, the display shows «DFFF».
E. Removal of all: press 1 to switch programming modes, select the mode which is displayed by the letter E and press the button 4 (OK). the display shows «EALL», which means a complete erasure of the memory of the receiver and the removal from it of all registered transmitters.
After the receiver settings, unplug the receiver from the programmer.
Shenzhen Chungyao Technology Co.; Ltd
Shenzhen Yaoertai Technology Development Co.,Ltd
address: 6th Floor block 27,Lianchuang Technical Zone, Bulan Road, Longgang district, Shenzhen,P.R.China
zip code: 518119
contact person: Alice zhou
phone/what's app: +86-18038019159
Email:alice@szyet.com
